The enclosure also houses up to two (2) additional Super Switch Takeover Modules, which increases your capacity to convert up to 24 wired sensors to wireless zones.
Are you looking to upgrade an existing wired security system to a wireless one? Whether you are replacing an older, wired security system or want to retrofit the pre-wired security sensors common to new construction, the 2GIG Hardwire Conversion Kit is the ideal solution and is easy to install. Leveraging 2GIG’s patented wireless takeover technology, each kit includes one (1) Super Switch Takeover Module which converts up to eight (8) wired sensors to 2GIG wireless zones. The kit also includes a Power Supply Board with backup battery charging circuit, a Grounded Plug-in Transformer, and an ABS plastic enclosure that includes a dedicated space for your backup battery (battery not included).
The enclosure also houses up to two (2) additional Super Switch Takeover Modules, which increases your capacity to convert up to 24 wired sensors to wireless zones.
The sensor (Model 2GIG-TILT1-345) is designed for applications where the tilt status of an asset, such as a garage door, needs to be monitored. Other uses might include: mailbox doors, large pet doors, or hinged storm cellar doors. The tilt sensor communicates with the control panel using the 345 MHz frequency. Once the sensor is tilted to 45 degrees, the sensor will transmit to the panel. The sensor will also send a restore signal when the sensor it returned to less than 45 degrees.
The 2GIG-TILT1-345 is equipped with a cover tamper switch and low battery monitoring. If the case of the Tilt Sensor is removed for any reason, the radio transmitter will send a tamper alert. Should the battery voltage drop below a prescribed level, the sensor will send a low battery report indicating that the battery should be replaced. The 2GIG-TILT1-345 is compatible with GC2 firmware revisions 1.14 and higher.
LTE Network
Model Number: 2GIG-LTEV1-A-GC2
Model Number: 2GIG-LTEV1-A-GC3
UPC Code: 817082012995
Thin Door/Window contact.
For narrow applications, sensor is only 3/4" wide
Fully supervised
Rare earth magnet
Supports internal and external contacts
Can be used for 2 zones of protection
Lithium battery
Transmits 345 MHz
ETL Listed
Wireless touch screen keypad
Full color touch screen interface
Same easy-to-use interface as the GC2 panel
Add up to 4 wireless touch screen keypads to 1 system
See and hear system status, chimes and alerts
Requires XCVR2-345
English
The 2GIG Passive Infrared Motion Detector is a wall-mounted unit with wide-angle motion protection. It communicates with the control panel using the 345 MHz frequency. When set to High (HI) Sensitivity Mode, the PIR has a maximum range of 30 ft deep x 50 ft wide (9.1 m x 15.2 m). The PIR’s pet-immune feature can be set to tolerate animals up 55 lbs.
2GIG’s Wireless Smoke/Heat/Freeze Alarm is a 3xAAA battery‐powered wireless alarm intended for use in a 2GIG system. The alarm has a built‐in wireless transmitter, which communicates with the 2GIG Control Panel. When smoke, excessive heat or cold is detected, the alarm sounds a loud local alarm and the built‐in transmitter sends a signal to the Control Panel. This alarm is designed to provide protection within a 35‐foot radius of the unit. The 2GIG‐SMTK3‐345 can send alarm, tamper and battery condition messages to the Control Panel.
The sensor (Model 2GIG-TILT1-345) is designed for applications where the tilt status of an asset, such as a garage door, needs to be monitored. Other uses might include: mailbox doors, large pet doors, or hinged storm cellar doors. The tilt sensor communicates with the control panel using the 345 MHz frequency. Once the sensor is tilted to 45 degrees, the sensor will transmit to the panel. The sensor will also send a restore signal when the sensor it returned to less than 45 degrees.
The 2GIG-TILT1-345 is equipped with a cover tamper switch and low battery monitoring. If the case of the Tilt Sensor is removed for any reason, the radio transmitter will send a tamper alert. Should the battery voltage drop below a prescribed level, the sensor will send a low battery report indicating that the battery should be replaced. The 2GIG-TILT1-345 is compatible with GC2 firmware revisions 1.14 and higher.
516-249-8800
About Us
Events
Locations
Line Card
Solutions
45 Cain Drive, Plainvew, Ny 11803 
516-249-8800
sales@dsgdist.com