OUTPUT |
Output Volt Amp Capacity (VA) |
1500 |
Output kVA Capacity (kVA) |
1.50 |
Output Watt Capacity (Watts) |
900 |
Output kW Capacity (kW) |
0.90 |
Nominal Output Voltage(s) Supported |
110V; 115V; 120V |
Nominal Voltage Details |
115v nominal output in battery mode |
Frequency Compatibility |
60 Hz |
Output Voltage Regulation (Line Mode) |
-18%, +8% |
Output Voltage Regulation (Battery Mode) |
+/- 5% |
Output Receptacles |
(8) 5-15R |
Output AC Waveform (AC Mode) |
Sine wave |
Output AC Waveform (Battery Mode) |
PWM sine wave | |
INPUT |
Rated input current (Maximum Load) |
8.6A |
UPS Input Connection Type |
5-15P; Right-Angled |
Input Circuit Breakers |
10A |
UPS Input Cord Length (ft.) |
6 |
Recommended Electrical Service |
15A 120V |
Input Phase |
Single-Phase | |
BATTERY |
Full Load Runtime (min.) |
4 min. (900w) |
Half Load Runtime (min.) |
12 min. (450w) |
External Battery Pack Compatibility |
BP24V15RT2U (limit 1) |
DC System Voltage (VDC) |
24 |
Battery Recharge Rate (Included Batteries) |
Less than 4.5 hours from 10% to 90% |
Internal UPS Replacement Battery Cartridge |
See RBC Selector for replacement battery information |
Battery Access |
Battery access door enables hot-swappable, user replaceable internal battery |
Expandable Runtime |
Yes | |
VOLTAGE REGULATION |
Voltage Regulation Description |
Automatic voltage regulation (AVR) maintains line power operation with an input voltage range of 75 to 147 |
Overvoltage Correction |
Input voltages between 128 and 147 are reduced by 12% |
Undervoltage Correction |
Input voltages between 93 and 107 are boosted by 14% |
Severe Undervoltage Correction |
Input voltages between 75 and 92 are boosted by 30% | |
USER INTERFACE, ALERTS & CONTROLS |
Front Panel LCD Display |
LCD interface reports Input Voltage, Output Voltage, Battery Charge Percentage, Estimated Runtime in Minutes, Load Percentage, Load Watts; Additional LCD icons report battery charge level (5 "bars"), Line Power Mode, Battery Mode, Replace Battery and Auto-Voltage Regulation / AVR status; LCD interface control options include Alarm Disable, Display Scrolling, Initiate Self-test, LCD brightness, External Battery setting and line sensitivity |
Switches |
2 Switches control off/on power status and alarm-cancel/self-test operation |
Alarm Cancel Operation |
Power-fail alarm can be silenced using alarm-cancel switch; once silenced, alarm will re-sound to indicate low-battery status |
Audible Alarm |
Audible alarm indicates power-failure and low-battery conditions; Alarm can be permanently silenced via LCD interface | |
SURGE / NOISE SUPPRESSION |
UPS AC Suppression Joule Rating |
1038 |
UPS AC Suppression Response Time |
Instantaneous |
UPS Dataline Suppression |
1 line TEL/DSL (1 in / 1 out); 10/100Base T Ethernet |
EMI / RFI AC Noise Suppression |
Yes | |
PHYSICAL |
Included Mounting Accessory Description |
Pair of mounting ears enable tower and 2-4 post rackmount installation |
Installation Form Factors Supported with Included Accessories |
Tower |
Primary Form Factor |
Rackmount |
UPS Power Module Dimensions (hwd, in.) |
3.5 x 17.3 x 10.5 |
Rack Height (U Spaces) |
2 |
Minimum Required Rack Depth (inches) |
14 |
UPS Power Module Weight (lbs.) |
29 |
UPS Power Module Weight (kg) |
13.15 |
Shipping Dimensions (hwd / in.) |
7.400 x 15.000 x 21.200 |
Shipping Weight (lbs.) |
33.2000 |
Cooling Method |
Fan |
UPS Housing Material |
Polycarbonate |
Primary UPS Height (mm) |
889 |
Primary UPS Width (mm) |
4,394 |
Primary UPS Depth (mm) |
2,667 | |
ENVIRONMENTAL |
Operating Temperature Range |
+32 to +104 degrees Fahrenheit / 0 to +40 degrees Celsius |
Storage Temperature Range |
+5 to +122 degrees Fahrenheit / -15 to +50 degrees Celsius |
Relative Humidity |
Up to 95%, non-condensing |
AC Mode BTU / Hr. (Full Load) |
78 |
Battery Mode BTU / Hr. (Full Load) |
721 |
AC Mode Efficiency Rating (100% Load) |
97% | |
COMMUNICATIONS |
Communications Interface |
USB (HID enabled); DB9 Serial; Contact closure |
Network Monitoring Port Description |
Supports detailed monitoring of UPS and site power conditions; DB9 port also supports contact-closure messaging for power-fail (pins 1 & 9) and power-restored (pins 1, 8) |
PowerAlert Software |
For local monitoring via the UPS’s built-in communication ports, download PowerAlert Local software at http://www.tripplite.com/poweralert |
Communications Cable |
USB and DB9 Serial cabling included |
WatchDog Compatibility |
Supports Watchdog application, OS and hard-reboot restart options for remote applications | |
LINE / BATTERY TRANSFER |
Transfer Time |
4 milliseconds AC to battery mode / 3 milliseconds battery to AC mode |
Low Voltage Transfer to Battery Power (Setpoint) |
75 |
High Voltage Transfer to Battery Power (Setpoint) |
147 | |