Thin Door/Window contact.
For narrow applications, sensor is only 3/4" wide
Fully supervised
Rare earth magnet
Supports internal and external contacts
Can be used for 2 zones of protection
Lithium battery
Transmits 345 MHz
ETL Listed
Glass break detector.
Monitors for the sound of breaking glass
Two test LEDs
Dual shatter recognition technology
Lithium battery
Transmits 345 MHz
ETL Listed
Wireless touch screen keypad
Full color touch screen interface
Same easy-to-use interface as the GC2 panel
Add up to 4 wireless touch screen keypads to 1 system
See and hear system status, chimes and alerts
Requires XCVR2-345
English
Replacement Power Supply
• High efficiency switching power supply
• 120 VAC @ 60 Hz input
• 14 VDC @ 1700 mA output
• Screw terminals for wiring to the
control panel
• Includes retaining bracket for
standard and Decora style outlets
• For GC2 or GC3
Replacement Power Supply • High efficiency switching power supply • 120 VAC @ 60 Hz input • 14 VDC @ 1700 mA output • 10’ cable • Barrel connector simplifies installation process • For GC2 or GC3
Model Number: 2GIG-DREC2-319
Important User Instructions: In order for the Fall Detector Pendant to function, it needs to be added to the system by a professional installer. The Fall Detector is an accessory and requires a Security or PERS system to connect to the monitoring services.
Model Number: 2GIG-F1-345
FireFighter is the newest innovation from Encore Controls Inc. It is the easiest, most cost effective way to add smoke alarm monitoring to your 2GIG control panel. FireFighter’s unique technology monitors the existing UL smoke detectors within the home. When an alarm is detected a wireless signal is sent to the control panel which in turn contacts the central monitoring station. With interconnected hardwired smoke detectors found in most homes today, only one FireFighter is needed to monitor ALL the smoke detectors within the home.
Once the sensor probe detects the presence of water for three (3) minutes, the integral transmitter will send a wet alarm transmission to the security/control panel. The probe will also send a restore (dry) report when the presence of liquid is no longer detected by the flood probe for three (3) minutes. For flood reporting, the sensor requires the installation of the supplied external flood probe. The sensor is capable of detecting clean or dirty fresh water, salt water, or tap water.
The 2GIG Passive Infrared Motion Detector is a wall-mounted unit with wide-angle motion protection. It communicates with the control panel using the 345 MHz frequency. When set to High (HI) Sensitivity Mode, the PIR has a maximum range of 30 ft deep x 50 ft wide (9.1 m x 15.2 m). The PIR’s pet-immune feature can be set to tolerate animals up 55 lbs.
The 2GIG Passive Infrared Motion Detector is a wall-mounted unit with wide-angle motion protection. It communicates with the control panel using the 345 MHz frequency. When set to High (HI) Sensitivity Mode, the PIR has a maximum range of 30 ft deep x 50 ft wide (9.1 m x 15.2 m). The PIR’s pet-immune feature can be set to tolerate animals up 55 lbs.
Model Number: 2GIG-SDS1-345
2GIG’s Wireless Smoke/Heat/Freeze Alarm is a 3xAAA battery‐powered wireless alarm intended for use in a 2GIG system. The alarm has a built‐in wireless transmitter, which communicates with the 2GIG Control Panel. When smoke, excessive heat or cold is detected, the alarm sounds a loud local alarm and the built‐in transmitter sends a signal to the Control Panel. This alarm is designed to provide protection within a 35‐foot radius of the unit. The 2GIG‐SMTK3‐345 can send alarm, tamper and battery condition messages to the Control Panel.
The Super Switch is 2GIG’s wireless takeover module. This unit was designed to convert 8 hardwired zones into eight wireless zones, make installation simple, and work with existing 12‐volt control panels. The module is to be mounted next to the existing Control Panel where the hardwired zones are connected. All of the zones on the Super Switch act as supervised wireless zones.
The enclosure also houses up to two (2) additional Super Switch Takeover Modules, which increases your capacity to convert up to 24 wired sensors to wireless zones.
The sensor (Model 2GIG-TILT1-345) is designed for applications where the tilt status of an asset, such as a garage door, needs to be monitored. Other uses might include: mailbox doors, large pet doors, or hinged storm cellar doors. The tilt sensor communicates with the control panel using the 345 MHz frequency. Once the sensor is tilted to 45 degrees, the sensor will transmit to the panel. The sensor will also send a restore signal when the sensor it returned to less than 45 degrees.
The 2GIG-TILT1-345 is equipped with a cover tamper switch and low battery monitoring. If the case of the Tilt Sensor is removed for any reason, the radio transmitter will send a tamper alert. Should the battery voltage drop below a prescribed level, the sensor will send a low battery report indicating that the battery should be replaced. The 2GIG-TILT1-345 is compatible with GC2 firmware revisions 1.14 and higher.
The 2GIG XCVR3-GC3 is a 900MHz transceiver and 345MHz receiver for the GC3 control panel. The GC3 is already equipped with a 345MHz receiver to speak with the 2GIG wireless transmitters like door contacts and motion detectors. This module physically replaces that receiver inside the GC3 panel. The XCVR3 adds the ability for the GC3 to communicate with 900MHz devices like the 2GIG-IMAGE2 image sensor. Without this module the panel is not capable of the required bi-directional signaling.
2GIG 2GIG-GC3E-345-K31
LTE Network
Model Number: 2GIG-LTEV1-A-GC2
Model Number: 2GIG-LTEV1-A-GC3
UPC Code: 817082012995
516-249-8800
About Us
Events
Locations
Line Card
Solutions
45 Cain Drive, Plainvew, Ny 11803 
516-249-8800
sales@dsgdist.com